KK6QHZ
| Joined: | Tue, Nov 18th 2014, 12:23 | Roles: | N/A | Moderates: | N/A |
Latest Topics
| Topic | Created | Posts | Views | Last Activity |
|---|---|---|---|---|
| 4NEC Model of droopy 1/4 problems | Jun 16th 2015, 23:18 | 5 | 5,685 | on 17/6/15 |
Latest Posts
| Topic | Author | Posted On |
|---|---|---|
| 4NEC Model of droopy 1/4 problems | KK6QHZ | on 17/6/15 |
| For my on sanity I reset the starting values to the conventional values and ran the optimization again. This time it converged near the expected values. I compared the results (SWR, Gain, Z) of the two sets of values and they quite similar. I can come up with several reasons why something like this could happen but have no clue as to which it might me. I will play around a bit more for my own education but conventional beats wierd results every time (-; Thanks for the conversation Zack and 73's. Jerry KK6QHZ |
||
| 4NEC Model of droopy 1/4 problems | KK6QHZ | on 17/6/15 |
| The lengths are in meters and 5/8 wavelength would be somewhere between 1.2 and 1.3 meters. (Your idea does raise the question of could a 5/8 wave work?) By my calculations, 0.6165 meters is about 3/10 of a wavelength. With these numbers in mind, I'm not sure that the 5/8 theory is the solution. Since I am new to 4NEC2, the problem could easily lie with how I modeled the antenna. Thanks for the idea Zack. Jerry KK6QHS |
||
| 4NEC Model of droopy 1/4 problems | KK6QHZ | on 16/6/15 |
| I was decided I to put a 2 meter antenna in my attic for use with my hand held and after browsing the web, decided a 1/4 wave "droopy" with 4 radials might be a good choice. Conventional wisdom is that the vertical should be slightly less than 1/4 wave. The radials should be a 1/4 wave and angled down at 45 degrees for impedance matching. It seemed like an educational venture to model the antenna with 4NEC2 to learn about antenna modeling. My optimized results do not agree with conventional wisdom and I am stumped as to why. Below are setup info, results and the card deck for NEC. Suggestions appreciated and thanks in advance. Jerry KK6QHZ 4NEC2 version 5.8.15 Optimization settings SWR=75 Gain=25 Rin=50 All others 0 Freq 146 0.6165 = Monopole length - Optimized 0.1993 = Radial length - Optimized 30.0 = Radial droop angle - Optimized 3.1 = Antenna height - estimated height in attic from true ground From 144 to 148Mhz SWR < 1.25 Gain essentially 4.7 Z 46 to 52 ohms NEC card deck CM 2 Meter 1/4 wave CM 4 radial drooping CM CE SY high=3.1 'Antenna height SY wlen=0.6165 'Monopole length SY rlen=0.1993 'Radial length SY droop=30.0 'Radial droop angle SY drpang=cos(droop) 'Adjustment for droop SY r1x=rlen*1.0*drpang 'Radial 1 X SY r1y=rlen*0.0*drpang 'Radial 1 Y SY r2x=rlen*-1.0*drpang 'Radial 2 X SY r2y=rlen*0.0*drpang 'Radial 2 Y SY r3x=rlen*0.0*drpang 'Radial 3 X SY r3y=rlen*1.0*drpang 'Radial 3 Y SY r4x=rlen*0.0*drpang 'Radial 4 X SY r4y=rlen*-1.0*drpang 'Radial 4 Y SY rz=high-(sin(droop)*rlen) GW 1 32 0 0 high 0 0 wlen+high 2.588mm 'Monopole GW 2 16 0 0 high r1x r1y rz 2.588mm 'Radial 1 GW 3 16 0 0 high r2x r2y rz 2.588mm 'Radial 2 GW 4 16 0 0 high r3x r3y rz 2.588mm 'Radial 3 GW 5 16 0 0 high r4x r4y rz 2.588mm 'Radial 4 GE 1 GN 0 0 0 0 5 0.001 EK EX 0 1 1 0 1 0 0 'Voltage source (1+j0) at wire 1 segment 1. FR 0 0 0 0 146 0 EN |
||
